一.密封設計
One. Seal design
首先，密封設計單元式門窗的密封是最關鍵的，密封的主要結構是單元和保護框的密封和保護框架之間以及細胞之間的細胞和保護盒應使用兩個或更多個之間和孔之間的密封件之間的密封連續橡膠密封.
First of all, the sealing design of unit doors and windows is the key, the main structure of the sealing unit and the protection box is sealed and protect the cell and protection box between frame and cell should be used between the seal between the continuous sealing rubber sealing between two or more and the hole.
密封結構設計的保護框架和所述孔之間應進行按照一個目標設計的形式的不同的結構，使幀之間的保護并且通常應該保持獨立的入口防水砂漿封孔處理后使用，可使用防水硅膠保護框然后密封的內部和外部飾面之間的窗口開口。
Between the seal protection frame structure design and the hole should be carried out in accordance with the design of a goal and the different forms of the structure, make the protection between frames and usually should keep an independent entrance waterproof mortar sealing treatment after use, can use waterproof silicone protective box and sealing between the internal and external surface of the window opening.
二、防水設計
Two. Waterproof design
防水設計是門窗的一大亮點，可以在門做防水模塊化設計雙重防水設計，設備本身的防水設計，在屏蔽盒的第二層的門窗，按排水孔和單元的設置，除了保護以外下一幀和單元主體連接的位置也打開排水孔。
Waterproof design is one of the highlights of the doors and windows, can do the waterproof design of double door module in the waterproof design, waterproof design of the equipment itself, in the second layer of shielding box doors and windows, according to the drainage holes and the unit set, in addition to the protection of the next frame and outside the unit body is connected to the position is open drain hole.
雨水或冷凝水在正常條件下從所述排水口部直接對身體直接排出室。如果細胞體和由于由單元主體和腔型材冷凝物的內部排水不良造成的雨水滲透或滲漏密封不嚴之間的保護盒可經過防水保護盒順利排出的第二層。
Rainwater or condensed water is directly discharged to the body from the drainage mouth under normal conditions. Second if the cell body and the protection box by unit body and internal cavity profile condensate caused by poor drainage of rainwater infiltration or leakage between the sealing waterproof protection box smoothly discharged.

第三、節能設計
Third, energy saving design
既使用防護盒，橋熱剖面窗單元(磨損條形或分配式均可)，絕熱結構寬度可以調整，根據節能目標的要求。由于單位門窗界面設計，單腔插頭結構，前門窗單元可以容易地連接到彈性絕緣材料的一側(擠出聚苯乙烯材料或聚氨酯材料)，能有效地阻礙剪接單元的空腔內部空氣流通，節能效果遠遠超過其他同類節能窗，而且還起到了隔音，降噪的效果。
The protection box is used, the bridge thermal section window unit (wear strip or distribution type can be), the width of the adiabatic structure can be adjusted, according to the requirements of the energy saving target. Because the unit window interface design, single cavity plug structure, one side of the front door unit can be easily connected to the elastic insulating material (extruded polystyrene material or polyurethane material), can effectively retard the splicing unit inside the cavity air circulation, energy saving effect is far more than other similar energy-saving windows, but also played the sound insulation, noise reduction effect.
四、抗震設計
Four, aseismic design
單元式門窗一個特殊的插件安裝相適應的結構使窗體的主體結構位移能力增 強，能有效吸收地震作用，溫度變化，層間位移，比傳統的門更適合不同地區的抗震要求。
A special plug-in door and window installation with a suitable structure can enhance the displacement capacity of the main structure of the form, and effectively absorb the earthquake effect, temperature change and interstory displacement, which is more suitable for seismic requirements in different areas than traditional doors.
感謝您的閱讀，此文的文章來源：鋁切割設備更多的內容和問題請點擊：http://hnyfqpj.cn 我們會繼續努力的為您提供服務，感謝您的支持！
Thank you for reading. The source of this article is aluminum cutting equipment. More contents and questions, please click: http://hnyfqpj.cn, we will continue to work hard to provide services for you, thank you for your support.