一看用料.優質的鋁合金門窗設備所用的鋁型材,厚度、強度和氧化膜等,應符合有關的國家標準規定,壁厚應在1.2毫米以上,抗拉強度達到每平方米毫米157牛頓,屈服強度要達到每平方毫米108牛頓,氧化膜厚度應達到10微米.如果達不到以上標準,就是劣質鋁合金門窗設備,不可使用.
A look at the material. Aluminum Alloy used aluminum doors and windows equipment quality, thickness, strength and oxide film, shall conform to the relevant provisions of the national standard, the wall thickness should be more than 1.2 mm, the tensile strength of 157 mm per square metre of Newton, yield strength to reach 108 per square millimeter of Newton, the thickness of the oxide film should reach 10 micron. If not up to the above standard, it is inferior Aluminum Alloy doors and windows equipment, can not be used.

二看加工.優質的斷橋鋁門窗設備,加工精細,安裝講究,密封性能好,開關自如.劣質的鋁合金門窗設備,盲目選用鋁型材系列和規格,加工粗制濫造,以鋸切割代替銑加工,不按要求進行安裝,密封性能差,開關不自如,不僅漏風漏雨和出現玻璃炸裂現象,而且遇到強風和外力,容易將推拉部分或玻璃刮落或碰落,毀物傷人.

Two see. The aluminum doors and windows processing equipment, high precision machining, installation stress, good sealing performance, switching freely. Aluminum Alloy inferior door window equipment, choose aluminous profile series and specifications, processing by saw cutting instead of crudely made, milling, no installation required, poor sealing performance, the switch does not freely, not only air leaks and glass burst phenomenon, and encountered strong winds and force, easy to push and pull part or glass fall or drop, and destroy wounding.
三看價格.在一般情況下,優質斷橋鋁門窗設備備因生產成本高,價格比劣質鋁合金門窗設備要高30%左右.有些有壁厚僅0.6-0.8毫米鋁型材制作的鋁合金門窗設備,抗拉強度和屈服強度大大低于國家有關標準規定,使用很不安全.
Three see price. In general, high quality aluminum doors and windows equipment because of its high production cost, the price ratio of Aluminum Alloy inferior door window equipment is 30% higher. Some have only 0.6-0.8 mm aluminum production equipment Aluminum Alloy window wall thickness, tensile strength and yield strength is much lower than the relevant national standard, it is not safe to use.
此外,目前加工鋁合金門窗設備的個體戶較多,他們不懂得鋁合金門窗設備的結構特點及其性能.為了降低成本偷工減料,以次充好,產品的隱患較大,一般不宜采用.選用正規鋁合金門窗設備生產廠家的產品. 這里要特別說明一點:現在的國家標準的型材厚度為1.4mm,如果供應商選擇的是1.2mm或者1.0mm壁厚甚至更薄的材料的話,都是屬于不達標的產品,請大家在選購時注意.
In addition, the current processing equipment more Aluminum Alloy doors and windows of the self-employed, they do not understand the structure characteristics and performance Aluminum Alloy doors and windows equipment. In order to reduce the cost of shoddy work, shoddy, the hidden trouble of the product is large, the general should not be used. It is best to choose the regular Aluminum Alloy doors and windows equipment manufacturers products. It must be clear: the thickness of the profile now the national standard is 1.4mm, if the supplier selection is 1.2mm or 1.0mm thickness even thinner material, are substandard products, please pay attention at the time of purchase.
本文由 鋁切割設備整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://hnyfqpj.cn/我們會有更多精彩內容等你查看
This article is arranged and released by the aluminum cutting equipment. Do you know something about it? Click more on the content: http://hnyfqpj.cn/, we will have more wonderful content for you to view